----------------------------------------------------------------------- Wilcox Associates, Inc. PC-DMIS GEAR Installation Notes: ----------------------------------------------------------------------- ****************************************************************************************************** PC-DMIS GEAR v2.3 ReadMe File ****************************************************************************************************** ----------------------------------------------------------------------------------------------- PC-DMIS GEAR Version 2.3 (built on Jul 16, 2010) ----------------------------------------------------------------------------------------------- The problems listed below are fixed in this version: ======================================================== 268440 - Quality munber for ffB is not right. 268278 - Ensure Gear adheres to Windows 7 recommendation for file locations. 268244 - When I try to install gear v2.3 QA build 324, I get an error, and it will not complete the install. 267922 - After canceling Master Flank data collection, I get an unhandled exception error. 267911 - When I answered NO to import the master flank data, it was imported anyway. 267866 - End Z coordinate for helix measurement can not be saved 267859 - There is some confusion with measuring new topography. 267858 - When I define a new Bevegl Gear, the Topography measurement is enabled but the tooth quantity is set to 0. 267793 - I get an Unhandled Exception Error when trying to define the master flank data. 267239 - Why does this gear prompt not respond to the UJB jogbox return key? 267229 - The Gear application does not switch to the analog probe for measurement. 267228 - The spiral bevel gear package only allows me to use the same single probe for pitch as I use for topography. 267227 - When I canceled alignment of the Gear, the message indiated it aligned successfully. 267071 - Verify the value of tip/root circle diameter to check if it is a value larger than 0.0 before measuring the gear. 267026 - The SP600 errors out after measuring one lead scan. 267025 - When trying to measure gear lead with a TP2, the scan does not stop. 267024 - The SP600 keeps crashing into the external helical spur gear. 267009 - Get an unhandled exception error when I try to run this Spiral Bevel Gear 266993 - After migrating the gear file of GEAR1.8 into GEAR2.2, Span Over Teeth is wrongly set to be evaluated. 266854 - This spiral bevel gear program will no longer run, I get an Unhandled Exception Error. 266852 - The Spiral Bevel Gear report is not maximized. 266846 - The Gear program does not rotate the analog probe for measurement. 266808 - Cannot see results on gear software. 266639 - The probe crashes during a move with this external helical spur gear. 266607 - When I try to run this (Internal Spur) gear measurement, I get an unhandled exception error. 266440 - When I try to open this old .GEAR file, I get a couple of memory related errors. 266429 - With the latest Gear install, it cannot find/create the part program. 266393 - When I try to run this Gear off-line, I get an application error. 266364 - PC-DMIS is not maximized when Gear's tring to measure a gear. 266242 - Single pitch deviation is fpt in ISO. 266171 - When I try to import this Gear DEF file, I get an Unhandled Exception Error in Define dialog. 266166 - Disabling Pitch measurement leaves me confused. 266018 - Profile curve and Helix/Lead curve are wrongly created in two separate report page when unckecking Measure now option in profile definiction dialog. 265859 - Add the localized help files into installer and change code to open specified help file according to the current language in GEAR. 265850 - Some of the Gear help files have an odd header displayed. 265779 - Probe was collision to top surface of bevel gear in DCC reference points. 265680 - After aligning gear, the execution dialog sit there doing nothing. 265637 - Gear changes the program marking when I use an existing program. 265617 - fHb tolorance calculated by Gear as default tolerance is a little different frorm the value from ISO1328 265529 - the tolerance evaluation range line dose not display one line. 265528 - Probe crash when measure profile only 265513 - Gear will not run on my system any longer. 264932 - When I program a Clearance Plane for the Gear Alignment, it gets hardcoded into a Move statement as well. 264931 - The tab order in the Align Gear dialog is not correct.. 264239 - Using an INCH gear measurement, some of the parameters on the report are in mm. 264024 - Parameter tree window is not updated with the change in Definition dialog. 263778 - Cannot measure a gear from the Gear application, only direclty from PC-DMIS. 263588 - clearance doesn't work correctly in gear 2.2 263360 - The evaluation range don't work in Helix/Lead evaluation. 262220 - Each time that a job is sent to the Printer we have to manually press Resume on the printer to complete the job... 262213 - Loading Helix/Gear data from the part program takes about 6-7 minutes for this file,,,, 262210 - Gear Report Window should open Maximized after execution completes so that it is more visible... 264895 - Span : no nom. in report and teeth number is n+1 264201 - Gear crashes on startup in Vista X64.... 264167 - When I define a new bevel gear and press the Calculate Tols button, I get an unhandled exception error. 264155 - Customer needs an average value of FA, fHA, ffA and FB, fHB, ffB to be output to report. 264130 - When I try to use SaveAs over the current name, I get an error. 264119 - Customer needs more information output to Gear report. 263956 - Fb/fHb/fBf calculation problem 263950 - customized report for KA customers 255444 - When I cancel and re-start the Gear alignment procedure, it keeps appending to the existing part program. 255441 - The Gear scanning density keeps getting set to 0.001. 255529 - Using the spacebar when entering a filename causes the cursor to move to the start of the line. 262219 - Cannot shut off PDF output after enabled... 262218 - Printer settings not being saved and will not print to a Printer after complete execution.... 262217 - Clearance Height is coming in from a 1.8 file as 0.00.... 262216 - The Gear Measurement Setup dialog shows "GEARALN" in the Probefile path... 262215 - Discrepancy between Pitch/Runout settings dialog and printed report.... 262783 - The tooth thickness indicates out, but the number are within tolerance. 262021 - PC-DMIS rotates a wrong tip angle to take two clocking points while aligning gear in PC-DMIS Gear v2.2 RC 261959 - Gear always create new part program for Bevel Gear measurement even if I unselect GENERATE item. 261889 - Created program has "Relearn" type of scans but the probe is TTP (TP20) 261729 - Dimension Over Ball is not calculated correctly. 261704 - The STATUS WINDOW for v2.2 gear do not stay off it is turned off after shutting down gear and re-opening. 261661 - Wrong setting in log file folder will cause Gear to crash in the second run. 261547 - It should be two zeros evaluation value in pitch evaluation for one tooth missing's incomplete. 261519 - Although the Touch Trigger option is seelected for Scan Type, it still uses analog scanning for profile. 261497 - To align a spur gear, I select "import an initial alignment" to align gear, the initial alignment name is incorrectly written in part program. 258553 - Move clearplane is needed in dcc plane for gear alignment.